Vaisala PTU300 Guia do Utilizador Página 160
- Página / 217
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
User's Guide _______________________________________________________________________
158 __________________________________________________________________ M210796EN-G
Table 36 Error Messages
Error Code
Error Message
Action
E0
Humidity sensor measurement
malfunction.
Check the integrity of the humidity probe
and the probe cable. Clean the probe from
dirt, water, ice or other contaminants.
E1
Humidity sensor short circuit
E2
Humidity sensor open circuit
Check the integrity of the humidity probe
and the probe cable.
E3
Temperature sensor open circuit.
E4
Temperature sensor short circuit.
Check the integrity of the humidity probe
and the probe cable. Clean the probe from
dirt water, ice or other contaminants.
E5
Temperature measurement
malfunction
E6
Temperature sensor current leak.
Check the integrity of the humidity probe
and the probe cables. Clean the probes
from dirt, water, ice or other contaminants.
E7
Internal ADC read error
Internal transmitter failure. Remove the
transmitter and return the faulty unit to
Vaisala Service.
E8
Additional temperature sensor
short circuit
Check the integrity of the temperature
probe and the probe cable. Clean the
probe cable from dirt, water, ice or other
contaminants.
E9
Checksum error in the internal
configuration memory
Internal transmitter failure. Remove the
transmitter and return the faulty unit to
Vaisala Service.
E10
Internal EEPROM read error
E11
Internal EEPROM write error
E12 … E13
Add-on module 1 (or 2)
connection failure
Turn off the power and check the module
connection. Turn on the power.
E14
Device internal temperature out of
range
Ensure that the operating temperature is
within the valid range.
E15
Internal RAM memory or software
checksum error
Internal transmitter failure. Remove the
transmitter and return the faulty unit to
Vaisala Service.
E16 … E17
Pressure measurement failure in
add-on module slot 1or 2
Disconnect power and check pressure
module connection.
E18
Internal ADC reference voltage
out of range
Internal transmitter failure. Remove the
transmitter and return the faulty unit to
Vaisala Service.
E19
Internal analog output reference
voltage out of range
E20 … E22
Configuration switches for analog
output 1/2/3 set incorrectly
Check and re-set the switches, see page
55.
E24 … E25
Internal error in add-on module
1 (or 2)
Disconnect the power and check the
module connection.
E26
Communication module installed
in incorrect add-on module slot
Disconnect the power and change the
communication module to another module
slot.
E27
Pressure out of valid range
Check that assumed pressure is within
measurement range for the transmitter.
E28 … E29
Unknown/incompatible module
installed in add-on module slot 1
(or 2)
Ensure that the module is compatible with
the PTU300.
E30
Internal analog voltage out of
range
Internal transmitter failure. Remove the
transmitter and return the faulty unit to
Vaisala Service.
E31
Internal system voltage out of
range
Check that the supply voltage is correct
and the power supply can provide enough
power for the instrument.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 4 4
- CHAPTER 6 7
- CHAPTER 7 7
- CHAPTER 8 8
- APPENDIX A 9
- APPENDIX B 9
- APPENDIX C 9
- List of Figures 10
- List of Tables 12
- GENERAL INFORMATION 15
- Version Information 16
- Related Manuals 16
- Documentation Conventions 16
- ESD Protection 17
- Recycling 18
- Regulatory Compliances 18
- DNV Type Approval 19
- Patent Notice 20
- Trademarks 20
- Software License 21
- Warranty 21
- PRODUCT OVERVIEW 23
- Basic Features and Options 25
- Structure of the Transmitter 26
- 0604-060 27
- Probe Options 28
- 0911-067 29
- Warmed Probe PTU307 30
- INSTALLATION 31
- 133 (5.24) 32
- 59 (2.32) 32
- Thickness 32
- 9.5 (0.37) 32
- 0911-061 33
- Pole or Pipeline 34
- 0503-007 35
- 0503-041 35
- 0509-151 36
- 0503-008 36
- Panel Mounting Frame 37
- 0804-083 38
- Cable Bushings 39
- Grounding the Cables 40
- Alternate Wiring Systems 41
- WARNING 42
- 8-Pin Connector 43
- D-9 Connector 44
- CAUTION 45
- Probe Mounting 46
- 0507-024 47
- 0507-022 47
- PTU303 for General Use 48
- PTU307 for High Humidities 49
- Temperature Probe (Optional) 49
- Optional Modules 50
- Installation 51
- Warnings 52
- Third Analog Output 55
- Installation and Wiring 56
- RS-422/485 Interface 59
- Figure 33 4-Wire RS-485 Bus 61
- 1102-027 62
- LAN Interface 63
- WLAN Interface 64
- 0706-068 66
- OPERATION 67
- Display/Keypad (Optional) 68
- Reading 69
- 0604-055 70
- Missing Trend 71
- Graphic History 72
- 0706-030 73
- Information Display 74
- Menus and Navigation 75
- Rounding Setting 76
- Display Backlight Setting 76
- Display Contrast Setting 76
- Keypad Lock (Keyguard) 77
- Menu PIN Lock 77
- Configuring Display Alarms 78
- 0802-069 80
- 0802-070 80
- Serial Line Communication 83
- Service Port Connection 84
- Using the Service Port 85
- LAN Communication 86
- Wireless LAN Configuration 89
- Communication Protocol 92
- Terminal Program Settings 93
- 0810-070 94
- 0810-071 95
- List of Serial Commands 96
- Table 27 Pressure Commands 98
- Table 28 GPS Commands 98
- Table 29 Other Commands 98
- Serial Line 99
- FTIME and FDATE 102
- General Settings 103
- Limit RH Output Range 107
- Date and Time 108
- NMEA Data Format 109
- GPS Commands 110
- Using Display/Keypad 111
- Using Serial Line 112
- Data Filtering for Pressure 114
- Temperature 115
- Device Information 117
- Serial Output Settings 121
- Data Recording 125
- Deleting the Recorded Files 128
- Analog Output Settings 129
- Analog Output Quantities 130
- AMODE/ASEL 131
- Analog Output Tests 132
- Operation of Relays 134
- 1102-007 135
- Hysteresis 136
- 1102-040 137
- Enabling/Disabling Relays 139
- Setting Relay Outputs 139
- Testing Operation Of Relays 142
- Sensor Functions 143
- Manual Chemical Purge 144
- Chemical Purge in Power Up 144
- Using Buttons On Motherboard 144
- Setting Sensor Heating 147
- Display/Keypad 148
- CHAPTER 5 149
- Taking Modbus into Use 150
- Enabling Serial Modbus 151
- Enabling Ethernet Modbus 152
- 1101-034 153
- 1101-036 153
- Diagnostic Modbus Counters 155
- Disabling Modbus 156
- MAINTENANCE 157
- Changing the Sensor 158
- Error States 159
- Table 36 Error Messages 160
- Technical Support 161
- Product Returns 161
- CALIBRATION AND ADJUSTMENT 163
- 0508-013 164
- Pressure Adjustment 165
- Example: 168
- Relative Humidity Adjustment 169
- Temperature Adjustment 177
- TECHNICAL DATA 181
- Relative Humidity 182
- Optional Temperature Probe 183
- Calculated Variables 184
- 1013 mbar) 185
- Probe Option) 186
- Inputs and Outputs 187
- Mechanics 188
- Modules 189
- RS-485 Module 190
- LAN Interface Module 190
- WLAN Interface Module 190
- Data Logger Module 190
- Spare Parts and Accessories 191
- 27.5 (1.08) 193
- 116 (4.57) 194
- 183 (7.20) 194
- 92 (3.62) 194
- 12 (0.47) 194
- 120 (4.72) 194
- 106 (4.17) 195
- 42 (1.65) 195
- Temperature Probe 196
- PROBE INSTALLATION KITS AND 197
- INSTALLATION EXAMPLES 197
- PTU307) 198
- 0508-032 199
- 0508-016 200
- Cable Gland 201
- 0508-018 202
- 0508-015 203
- 0508-022 203
- 0601-044 204
- CALCULATION FORMULAS 205
- 99.621 ×= 206
- MODBUS REFERENCE 209
- Register Map 210
- 16-Bit Integer Format 211
- Measurement Data (Read-Only) 212
- Status Registers (Read-Only) 213
- Configuration Registers 213
- Exception Status Outputs 214
- Diagnostic Sub-Functions 215
- Exception Responses 216
- *M210796EN* 217
Manuais e produtos relacionados com Componentes para dispositivos de segurança Vaisala PTU300
(105 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais